Beacon 200 Two Channel Wall Mount Controller by RKI Instruments
In stock
RKI Instruments Beacon® 200 two-channel wall-mount controller (115–220 VAC, no sensor): a powerful, low-cost, microprocessor-controlled fixed system controller for two points of gas detection.
Key benefits
- Simultaneous readout on 2 channels with backlit display of gas type and concentration
- Two alarm levels per channel; discrete and common relays rated 10 A to drive most external alarms and horns
- Connects directly to RKI LEL, oxygen, H2S or CO sensors, or any 4-20 mA transmitter (2 or 3 wire, 24 VDC)
- Sensors mount at the housing or wire remotely
- 4-20 mA outputs
- NEMA 4X housing for corrosion resistance and weather-tight seal; complies with lock-out/tag-out standards
- External reset switch silences alarm from outside the housing
- Wall mounting kit included
- Made in the USA
Specifications
Physical |
|
| Dimensions | Height: 10.5” 267 mm Width: 8.5” 216 mm Depth: 6.3” 158 mm |
| Enclosure | Wall mounting grey polycarbonate with hinged cover |
| Conduit Connection | 3/4” NPT conduit hubs, 3 provided. 2 for sensor wiring and 1 for power & relay wiring |
| Wiring Termination | Screw type terminal block, 14 gauge max |
| Controls | 4 internal push buttons for setup, programming, and calibration. 1 external push button for alarm reset |
Environmental |
|
| Operating Temp | -4°F to 122°F (-10°C to 50°C) |
| Storage Temp | -4°F to 158°F (-20°C to 70°C) |
| Relative Humidity | 0 – 100% RH |
| Enclosure Rating | NEMA-4X enclosure, waterproof, chemical, and weather resistant |
Inputs |
|
| Direct Wired Sensors | LEL, Oxygen, Carbon Monoxide, Hydrogen Sulfide Remote amp not required for less than 500 feet |
| 4-20 mA Sensors | Accepts any 4-20 mA transmitter (24 VDC, 2 or 3 wire). A wide variety of RKI/Riken sensors are available with 4-20 mA signals. (See list of detectable gases.) Wiring distances up to 5000 feet |
| Sampling Methods | Diffusion and sample draw heads available |
Outputs |
|
| Relays | 7 relays – 10 amp rating (at 115 VAC), SPDT isolated contacts. 2 relays for gas alarm levels per channel, plus 2 relays for common gas alarm and 1 common relay for malfunction. Relays fully programmable for: increasing or decreasing alarm, latching or self reset, normally energized or normally de-energized, time delay for alarm on and alarm off |
| 4-20 mA | Signal output, 4-20 mA (into 1000 ohms impedance maximum), per channel |
| 24 VDC | 24 VDC (350 mA max) output provided to operate sample drawing adapters or other accessories |
| Display | Alphanumeric display with backlighting. 20 characters per line; 4 lines each |
| Audible | Built-in audible alarm, 94 dB, mounted on enclosure Coded output: pulsing = gas alarm, steady = fail |
| Visual | 4 LED’s on the front cover for alarm status indication, pilot, and malfunction |
| Optional Expansion Cards | Individual 4-20 mA (or 1 – 5 VDC) outputs Heavy duty relay card (4 each @ 30 amps) |
Power |
110-240 VAC or 24 VDC standard. Battery backup option available |
Warranty |
One year materials and workmanship |
| Partial List Of Detectable Gases Many other gases or ranges available. Contact RKI for gases or ranges not listed. | |
| Ammonia (NH3) | 0 – 75.0 ppm |
| Arsine (AsH3 ) | 0 – 0.20 ppm |
| Boron Trichloride (BCl3) | 0 – 15.0 ppm |
| Carbon Dioxide (CO2) | 0 – 1.0 % |
| Carbon Monoxide (CO) | 0 – 300 ppm |
| Chlorine (Cl2) | 0 – 3.0 ppm |
| Chlorine Dioxide (ClO2) | 0 – 1.00 ppm |
| Chlorine Trifluoride (ClF3) | 0 – 1.00 ppm |
| Combustibles | 0 -100% LEL |
| Diborane (B2H6) | 0 – 30.0 ppm |
| Fluorine (F2) | 0 – 6.0 ppm |
| Hydrogen (H2) | 0 – 2000 ppm |
| Hydrogen Chloride (HCl) | 0 – 15.0 ppm |
| Hydrogen Fluoride (HF) | 0 – 9.0 ppm |
| Hydrogen Sulfide (H2S) | 0 -100.0 ppm |
| Nitric Oxide (NO) | 0 -100.0 ppm |
| Nitrogen Dioxide (NO2) | 0 – 15.0 ppm |
| Nitrogen Trifluoride (NF3) | 0 – 30.0 ppm |
| Oxygen (O2) | 0 – 25.0 % |
| Ozone (O3) | 0 – 1.0 ppm |
| Phosphine (PH3) | 0 – 1.0 ppm |
| Silane (SiH4) | 0 – 15.0 ppm |
| Sulfur Dioxide (SO2) | 0 – 30.0 ppm |
| TEOS (Si(OC2H5)4) | 0 -15/30 ppm |
Specifications subject to change without notice.
Product information supplied by the manufacturer (RKI Instruments).
Product codes
SKU: 72-2102RK
Couldn't load pickup availability
Discuss your requirements with Russmill Safety: sales@russmillsafety.com.
Selection & specifications
Selection & specifications
Review the product description, available variants and manufacturer’s specifications before ordering. PPE must be selected for the hazards and requirements of your workplace.
Shipping & returns
Shipping & returns
Review our Shipping Policy and Refund Policy for current terms.
Care & product support
Care & product support
Follow the manufacturer’s care, inspection and replacement instructions. Need clarification? Contact customerservice@russmillsafety.com with the product name or SKU.
Available payment methods are displayed at checkout. Review your order and delivery details before completing payment.
Quick order list
Match equipment to your workplace hazards and the manufacturer’s published specifications. Check sizing, compatible components and intended use before ordering.
Read our Shipping Policy and Refund Policy. Contact our team about product and order requirements.
Send product names or SKUs, quantities, sizes and your destination to sales@russmillsafety.com to discuss your requirements.
